Getting Started with Plumbing Basics for Bathtub Installation
Call TodayWhat are your thoughts and feelings about How to Install a Bathtub Yourself?
Mounting a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open a wall to remove the old tub and place the new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have currently purchased a new tub and also don't require to change the setup of your previous water system pipes.
Your tools and also material list ought to make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic because of the restricted access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Safeguard the faucet in place with the maker supplied backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the bath tub up until the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water and check all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill up the tub as well as additionally examine the overflow outlet and the regular outlet for leakages.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub should wait until the bath tub has been used a minimum of once as this will certainly settle it right into its final position.
Preparing for the Installation
Firstly, the supporting framework provided with the bath should be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, bring about issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealant can fracture rather very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that page about Installing A Bathtub when doing research the internet. Be sure to take the opportunity to share this content if you appreciated it. I appreciate reading our article about Installing A Bathtub.
For fast relief, call!